Csm unican manual

The data logger supports J with the full support of the transport protocol and online triggering of the Diagnostic Trouble Codes entailed in the DM1-message. The UniCAN 2 data loggers are offered in different hardware and software-expansion stages. New Eagle US offers two embedded data logger solutions, which both provide the capability for even Delphin Technology Germany has introduced its Expert Logger, a stand-alone data logger.

It is main Vector and CSM launched the E-Mobility measurement system for development of electric mobility appli All rights reserved. CAN Newsletter Online. Save as PDF. If the internet is used for data transmission, data integrity can be ensured by using the ftp command XCRC.

SSH2 provides protection against data theft and data corruption. Data can be transmitted via mobile communications modem while data recording continues without interruption. For maximum data security, the data transmission is binary.

The data transmission mode can be used to determine when the data logger should transmit data. Data can be transmitted when the ignition is switched on and off or periodically. The logger stands out for its very low power consumption in stand-by mode.

Important status information can be displayd live via "Live Monitoring" to check configuration and data recording. This makes commissioning much easier.

The following information is displayed: Status of the logger e. The UniCAN 3 ETH is a compact and robust data logger for the acquisition of data from various sources: With the Ethernet interface, nine CAN interfaces, digital inputs and outputs and numerous data transmission options, it can be used flexibly in any measurement task. At the same time they offer unique data security. The signals can be viewed using the configuration software CSMuniconf Version 3.

To be able to use the system signals, they must be integrated separately. To do this, select the signal source with a right click and insert the system signals. The desired signals can then be selected and added to a channel group. Simultaneous disconnection of ignition- and supply-cable is possible, but the following points must be observed:. A selection of channels can be combined in a channel group.

A total of up to eight channel groups can be created. In order to simplify the evaluation and to limit the data volume, filters can be defined that only allow data for certain ID groups to pass through. A total of up to eight message groups can be created. Is it possible to start the UniCAN at a special time?

Important: The wake-up time must be entered in UTC. To start the logger, the logger must be connected to the power supply. Deleting a channel from a channel group does not work. It is only possible to delete a channel group if no channel in the group is assigned to a condition.

If it is not possible to delete the selected channel, please check whether channels are assigned to conditions. If so remove the corresponding channel from the condition. Then it should be possible to delete the channel again. CANstim is an additional firmware option of the data logger. This firmware option enables Stimulation groups to be defined, which enable an initial, periodic and final transmission of constant message sequences via CAN bus when a trigger is activated.

A maximum of CAN messages can be sent periodically across all stimulation groups. Further information on the stimulation groups can be found in the UniCAN user manual in chapter 6. The number of firmware options can be extended even after logger purchase. Please contact your personal customer advisor or sales csm.

How can I establish the USB connection to the logger without constantly running a measurement? Connect the logger to the power supply and start the logger with terminal 15 until the connection is established. Then terminal 15 can be disconnected again. How many triggers are available for one configuration? A maximum of 32 trigger can be defined and assigned. It is also to configure channel groups with "no trigger".

This setting corresponds to the trigger "Always on" Thus, one trigger has been saved and another can be defined. A DBC with extended multiplex signal cannot be imported. The data logger only supports single unique multiplexer signals standard multiplexing. What is the maximum number of XCP channels that can be configured? If this value is exceeded, the UniCAN 3 reports a configuration error.

The logger starts several attempts to connect to the server. The transfer duration can be set in Uniconf under the properties of the transport configuration. The connection attempts are logged in the extended log file of the logger. In addition to other entries, the "SignalStrength" indicates the quality of the radio network. If this value is less than or equal to 10, the reception is too poor.